Weed Eater World

This site is dedicated to videos and products for maintaining and using your weed eater.

Carburetor Repair on Homelite SX135 Bandit Weed Wacker Part 1/2

Written By: Weed Eater Guy - Jan• 14•18


HOW TO REPAIR & Rebuild the Carburetor Homelite Grass Trimmers. Visist my channel for more repair videos; www.youtube.com

To Find your next Weedeater or Weedeater parts visit

our Weedeater store

Republished by Blog Post Promoter

You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.

25 Comments

  1. smallenginemaster1 says:

    what is that plastic piece call on the feul line and do you need to have it thanks

  2. th19940305 says:

    @penmoe23 Just go to a small engine shop and bring the old lines and theyll tell you wahat size you need

  3. penmoe23 says:

    I was wondering if you knew the model number for this weed eater. I need fuel line parts.

  4. donyboy73 says:

    @idalisponcepr make sure the gas cap is venting

  5. idalisponcepr says:

    i have homelite trimmer it starts fine when its cold.after its warm,causes the carburator to overflow fuel even when it not runing? you can see the fuel thru the carb and it won”t start.i replace tha same part you put in the video you call dframe and cleaning the carb but nting?do you know what the problem migt be?

  6. themovieguyawesome says:

    @donyboy73 i knew they were cheap…but ty for the info

  7. donyboy73 says:

    @themovieguyawesome they only cost a few bucks, you are better to put in a new one

  8. themovieguyawesome says:

    quick question, im tryna make a scooter w/ this exact engine…but it doesnt have a prime button. instead of buying a prime button is there any way i could just cover it and not cause any issues w/ the engine?

  9. donyboy73 says:

    @jasper60103 sounds like a carb issue

  10. jasper60103 says:

    Hi. I have the same weed trimmer (HomeLite SX-135). It starts and runs great initially. My problem is it’s starts bogging down at WOT after running for a while. I was wondering could this be a carb issue? I adjusted the low/high speed needles. It didn’t make a difference. I haven’t taken the carb off yet.

  11. donyboy73 says:

    @unrealsgt turn them out at 2 turns each because it will always run and then adjust from there it will end up being approx 1 1/2 turns out each when ur done

  12. unrealsgt says:

    What should the carb setting be at the high and low screws they are turned all the way in how i got it please message me bk i got walbro carb and same weedeater please help

  13. sniperbullet12 says:

    shouldnt u use carb cleaner

  14. sniperbullet12 says:

    thanks a lot

  15. donyboy73 says:

    @sniperbullet12 sounds like it needs a new carb kit

  16. sniperbullet12 says:

    i put a new fuel line and it still wont start the carbs dry and the rubbers dry and most gaskets r blown also the primer balub wont filll up with fuel it will only start with starter fluid for 3 sec what should i do

  17. sniperbullet12 says:

    i replaced the fuel line and it still wont starl i dont think its geting gas cause i got a spark plug and and i sparks it will only run for 3 sec if i use starter fuilid also the primer baulb does not fill up with fuel after i push it and every thing rubber is dry and some gaskets r blown what should i do

  18. sniperbullet12 says:

    ya thanks on more think my carbs kinda the same it a home lite sx135 and i got new fuel lines and now it still wont start its been siting for a long time and i took apart the carb and the gasket we blone and it was all rely dry wo that stop it from runing also the the primer balb would not fill with gas it like a inche in there and has no cracks

  19. donyboy73 says:

    @sniperbullet12 u mena the screen in the carb, no it is supposed to be very clean

  20. sniperbullet12 says:

    my screens full os greese is that supost to be there

  21. sniperbullet12 says:

    on my screen theres greese on top of the opening is that supost to be there

  22. donyboy73 says:

    @careydude jacks small engines dot com should have it

  23. careydude says:

    I have a broken choke lever on my homelite s1400 trimer. do you know the part number and where I could get one online?
    Thanks, Carey

  24. Raylep1 says:

    @donyboy73 Yeah it is a Zama 93

  25. donyboy73 says:

    @Raylep1 the kit u need is K10-WAT if it’s a walbro carb. it might be a zama carb.

Leave a Reply

Your email address will not be published. Required fields are marked *

Powered by Yahoo! Answers